GPS NTP Server - VCL-2156

VCL-2156 establishes a highly accurate phase-synchronized frequency and time base by synchronizing to the SPS (GNSS) satellites' atomic clocks to distribute synchronized time over packet based networks including Ethernet, Carrier Ethernet, IP and IP/MPLS Networks.

Product Brochure / Data Sheet

VCL-GPS-2145 GPS, IEEE-1588v2 PTP Grandmaster and Primary Reference Clock

GPS Grandmaster and Primary Reference Clock, IEEE-1588v2 PTP Grandmaster, Primary Reference Clock, NTP Server (IPv4 and IPv6). Provides IRIG-B, 1PPS, NMEA, 1/5/10MHz, 2.048MHz, 2.048Mbits with SSM, 1.544Mbits GPS referenced clock outputs. OCXO and Rubidium Holdover Clock options available.

GPS-2145-D GPS, IEEE-1588v2 PTP Grandmaster and Primary Reference Clock with 1+1 Redundant GPS

VCL-GPS-2145-R offers its 1+1 Redundant GPS, IEEE-1588v2 PTP Grandmaster, Primary Reference Clock, NTP Server (IPv4 and IPv6) which provides IRIG-B, 1PPS, NMEA, 1/5/10MHz, 2.048MHz, 2.048Mbits with SSM, 1.544Mbits GPS referenced clock outputs. OCXO and Rubidium Holdover Clock options available.

Product Brochure / Data Sheet

2145-SLV IEEE-1588 Slave PTPv2 Precision Time Protocol, Slave Clock solutions for ToD (Time-of-Day) and Frequency Synchronization

VCL-2145-SLV PTP (IEEE-1588v2) Slave for ToD (Time of Day) and Frequency Synchronization solution - synchronizes to PTP Grandmaster to provide IRIG-B, 1PPS, NMEA, 1/5/10MHz, 2.048MHz, 2.048Mbits clock outputs. OCXO and Rubidium Holdover Clock options available.

2112-SLV-LC IEEE-1588v2 Slave Clock for ToD (Time of Day) and Frequency Synchronization

VCL-2112-SLV-LC, Precision Time Protocol (PTP IEEE-1588v2) Slave Clock for ToD (Time of Day) and Frequency Synchronization - synchronizes to PTP Grandmaster to provide IRIG-B, 1PPS, NMEA, 1/5/10MHz, 2.048MHz, 2.048Mbits clock outputs. OCXO Holdover Clock option available.

VCL-TP, Teleprotection Equipment (C37.94 Optical Version)

8 Command Teleprotection Terminal (8 Nos. Tx & Rx independent command inputs & outputs for providing interconnection with Power Protection Relays). C37.94 Optical Interface, Single Mode 1310nm/ Multi-Mode 850nm / Multi-Mode 1310nm. Available power options: -24V DC, 48V DC, 110V DC, 250V DC.

VCL-TP, Teleprotection Equipment (G.703 64 Kbps co-directional Electrical Version)

8 Command Teleprotection Terminal (8 Nos. Tx & Rx independent command inputs & outputs for providing interconnection with Power Protection Relays) G.703 64Kbps,4-Wire co-directional interface. Available power options: -24V DC, 48V DC, 110V DC, 250V DC.

VCL-E1oP (2 E1 Port FE Version)

Orion Telecom Networks Inc. offers 'VCL-E1oP' (2 E1 Port FE Version) equipment supports transmission of up to 2 x E1 links over IP / Ethernet,pseudowire, MEF or MPLS networks.

VCL-E1oP (2 E1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-E1oP' (2 E1 Port GE Version) equipment supports transmission of up to 2 x E1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-T1oP (2 T1 Port FE Version)

Orion Telecom Networks Inc. offers 'VCL-T1oP' (2 T1 Port FE Version) equipment supports transmission of up to 2 x T1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-T1oP (2 T1 Port GE Version)

Orion Telecom Networks Inc. offers ' 'VCL-T1oP' (2 T1 Port GE Version) equipment supports transmission of up to 2 x T1 links over IP / Ethernet, pseudowire, MEF or MPLS networks

VCL-E1oP (4 E1 Port FE Version)

Orion Telecom Networks Inc. offers 'VCL-E1oP' (4 E1 Port FE Version) equipment supports transmission of up to 4 x E1 links over IP / Ethernet, MEF or MPLS networks.

VCL-T1oP (4 T1 Port FE Version)

Orion Telecom Networks Inc. offers 'VCL-T1oP' (4 T1 Port FE Version) equipment supports transmission of up to 4 x T1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-E1oP (8 E1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-E1oP' (8 E1 Port GE Version) equipment supports transmission of up to 8 x E1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-T1oP (8 T1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-T1oP' (8 T1 Port GE Version) equipment supports transmission of up to 8 x T1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-E1oP (16 E1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-E1oP' (16 E1 Port GE Version) equipment supports transmission of up to 8 x E1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-T1oP (16 T1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-T1oP' (16 T1 Port GE Version) equipment supports transmission of up to 8 x E1 links over IP / Ethernet, pseudowire, MEF or MPLS networks.

VCL-E1oP (32 E1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-E1oP' , 32 E1 Port GE Version of our TDM over IP equipment supports transmission of up to 32 x E1 links over IP / Ethernet, pseudowire, MEF or MPLS networks. Multiple units of the, 32 E1 Port GE Version of this equipment may be cascaded to support 32/64/128E1 Ports aggregation at the Central Office / MSC (Mobile Switching Center).

VCL-T1oP (32 T1 Port GE Version)

Orion Telecom Networks Inc. offers 'VCL-T1oP' , 32 T1 Port GE Version of our TDM over IP equipment supports transmission of up to 32 x T1 links over IP / Ethernet, pseudowire, MEF or MPLS networks. Multiple units of the, 32 E1 Port GE Version of this equipment may be cascaded to support 32/64/128 T1 Ports aggregation at the Central Office / MSC (Mobile Switching Center).

VCL-DS3oP (DS3 Version)

Orion Telecom Networks Inc. offers 'VCL-DS3oP', DS3 (T3) over Ethernet equipment provides transmission of one, point-to-point, DS3 (T3) link over an IP / Ethernet, pseudowire, MEF or MPLS network.

VCL-E3oP (E3 Version)

Orion Telecom Networks Inc. offers 'VCL-E3oP' (E3 over IP) equipment is used to transport a single E3 interface over an IP, MPLS or Ethernet network.

VCL-E1oP (2E1 Port IEEE-1588v2 Version)

VCL-E1oP' E1 over Packet (2 E1 Port IEEE-1588v2 Version) TDM over IP equipment supports transmission of up to 2 x E1 links over IP / Ethernet, MEF or MPLS networks and synchronization using IEEE-1588v2 protocol. The 'VCL-E1oP' E1 over Packet (2 E1 Port IEEE-1588 Version) TDM over IP equipment with IEEE-1588 protocol engine which provides a highly reliable clock recovery mechanism for extremely low jitter and wander control, even under variable network conditions.

VCL-E1oP (8E1 Port IEEE-1588v2 Version)

VCL-E1oP' E1 over Packet (8 E1 Port IEEE-1588v2 Version) TDM over IP equipment supports transmission of up to 8 x E1 links over IP / Ethernet, MEF or MPLS networks and synchronization using IEEE-1588v2 protocol. The 'VCL-E1oP' E1 over Packet (8 E1 Port IEEE-1588 Version) TDM over IP equipment with IEEE-1588 protocol engine which provides a highly reliable clock recovery mechanism for extremely low jitter and wander control, even under variable network conditions.

VCL-T1oP (2T1 Port IEEE-1588v2 Version)

'VCL-T1oP' T1 over Packet (2 T1 Port IEEE-1588v2 Version) TDM over IP equipment supports transmission of up to 2 x T1 links over IP / Ethernet, MEF or MPLS networks and synchronization using IEEE-1588v2 protocol. The 'VCL-T1oP' T1 over Packet (2 T1 Port IEEE-1588 Version) TDM over IP equipment with IEEE-1588 protocol engine which provides a highly reliable clock recovery mechanism for extremely low jitter and wander control, even under variable network conditions.

VCL-T1oP (8T1 Port IEEE-1588v2 Version)

'VCL-T1oP' T1 over Packet (8 T1 Port IEEE-1588v2 Version) TDM over IP equipment supports transmission of up to 8 x T1 links over IP / Ethernet, MEF or MPLS networks and synchronization using IEEE-1588v2 protocol. The 'VCL-T1oP' T1 over Packet (8 T1 Port IEEE-1588 Version) TDM over IP equipment with IEEE-1588 protocol engine which provides a highly reliable clock recovery mechanism for extremely low jitter and wander control, even under variable network conditions.

DS3 Echo Cancellers with VQE

Orion Telecom Networks Inc. provides robust and cost effective DS3 echo canceller with voice quality enhancement features for the long distance, wireline, wireless, (GSM, CDMA, TDMA), VoIP, satellite and radio communications. The VCL-EC, DS3 echo cancellers are offered to provide cancellation of upto 128ms echo tails. The echo canceller equipment is compliant to ITU-T G.164, G.165, G.168 (2000 / 2002) requirements for echo cancellation. The echo canceller solutions offers carrier-grade voice quality per AT&T Voice Quality Assessment Lab. The echo canceller supports fax / modem G.164 and G.165 (2100 Hz) tone disable function.

E1 Voice Echo Cancellers (Upto 10 Echo Canceller per Chassis)

E1 Voice Echo Canceller is a fully integrated 30 channel echo canceller that cancels echo up to 128ms. The VCL-EC128 offers disable tone detection. Each of the 30 channels cancels echoes up to 128ms and meets ITU-T G.165 and ITU-T G.168 requirements for echo cancellation. Inputs and Outputs are 120 Ohms, RJ45 E1s.

T1 Voice Echo Cancellers (Upto 10 Echo Canceller per Chassis)

T1 Voice Echo Canceller is a fully integrated 24 channel echo canceller that cancels echo up to 128ms. The VCL-EC128 offers disable tone detection. Each of the 24 channels cancels echoes up to 128ms and meets ITU-T G.165 and ITU-T G.168 requirements for echo cancellation. Inputs and Outputs are 100 Ohms, RJ45 T1s.

8 E1 Echo Cancellers with Voice Quality Enhancement (VQE) - with tail-displacement

Orion offers the industry's most compact 8, E1 echo canceller port solution in 19 inch, 1U (44mm height) chassis, with tail-displacement feature from 0ms. to 512ms - user selectable. Echo cancellation on each channel is 128ms. bi-directional. The 8 port E1 echo canceller solution offers a unique, user definable echo-tail displacement between 0ms. to 512ms. on the return path to cancel echo-tails, both at the near-end and the far-end, in the most demanding conditions.

8 T1 Echo Cancellers with Voice Quality Enhancement (VQE) - with tail-displacement

Orion offers the industry's most compact 8, T1 echo canceller port solution in 19 inch, 1U (44mm height) chassis, with tail-displacement feature from 0ms. to 512ms - user selectable. Echo cancellation on each channel is 128ms. bi-directional. The 8 port T1 echo canceller solution offers a unique, user definable echo-tail displacement between 0ms. to 512ms. on the return path to cancel echo-tails, both at the near-end and the far-end, in the most demanding conditions.

E1 Echo Cancellers - Compact 1U High

Orion offers a compact, robust and cost effective E1 echo canceller solution in 19 inch, 1U high (44mm height) chassis (accommodates 1, E1 echo canceller with telnet, per shelf). Echo cancellation on each channel is 64ms Bi-Directional / 128ms. Uni-Directional echo tails - user selectable.

T1 Echo Cancellers - Compact 1U High

Orion's latest compact, robust and cost effective T1 echo canceller solution in 19 inch, 1U high (44mm height) chassis (accommodates 1, T1 echo canceller with telnet, per chassis). Echo cancellation on each channel is 64ms Bi-Directional / 128ms. Uni-Directional echo tails - user selectable.

T1 Desktop Echo Cancellers

Orion Telecom Networks Inc. provides robust and cost effective T1 echo canceller and voice quality enhancement solutions for the long distance, wireline, wireless, (GSM, CDMA, TDMA), VoIP, satellite and radio communications. The VCL-EC, T1 echo cancellers are offered to provide cancellation of 64ms / 128ms (user selectable) echo tails. The echo canceller equipment is compliant to ITU-T G.164, G.165, G.168 (2000 / 2002) requirements for echo cancellation. The echo canceller solutions offers carrier-grade voice quality per AT&T Voice Quality Assessment Lab. The echo canceller supports fax / modem G.164 and G.165 (2100 Hz) tone disable function.

E1 Desktop Echo Cancellers

Orion's new compact (weight < 1 kg), robust and cost effective, E1 echo canceller solution in a desk top version (modem type). Echo cancellation on each channel is 64ms. / 128ms. Bi-Directional / Uni-Directional - user selectable.

E1 Quad Echo Cancellers (Upto 32 E1 Ports Per Chassis)

Orion Telecom Networks Inc. provides robust and cost effective E1 and T1 Quad echo canceller for the long distance, wireline, wireless, (GSM, CDMA), VoIP, satellite and radio communications. The Quad VCL-EC, E1 echo canceller card offers 4 x E1 Echo Cancellers in each card which provide cancellation of 64ms / 128ms (user selectable) echo tails. The echo canceller equipment is compliant to ITU-T G.164, G.165, G.168 (2000 / 2002) requirements for echo cancellation.

T1 Quad Echo Cancellers (Upto 32 T1 Ports Per Chassis)

Orion Telecom Networks Inc. provides robust and cost effective T1 and E1 Quad echo canceller for the long distance, wireline, wireless, (GSM, CDMA), VoIP, satellite and radio communications. The Quad VCL-EC, T1 echo canceller card offers 4 x T1 Echo Cancellers in each card which provide cancellation of 64ms / 128ms (user selectable) echo tails. The echo canceller equipment is compliant to ITU-T G.164, G.165, G.168 (2000 / 2002) requirements for echo cancellation.

VCL-HSL 64 E1 Port Hi-Z Monitoring Equipment

The VCL-HSL 64 Port E1 Hi-Z Monitoring Equipment is suitable for "non-intrusive" monitoring applications and may be used to monitor upto 32, "live" HSL E1 (High Speed Link) traffic links in both transmit and receive directions.

VCL-HSL 64 T1 Port Hi-Z Monitoring Equipment

The VCL-HSL 64 Port T1 Hi-Z Monitoring Equipment is suitable for "non-intrusive" monitoring applications and may be used to monitor upto 32, "live" HSL T1 (High Speed Link) traffic links in both transmit and receive directions.

64 Port Plus - T1 Monitoring GROOMER

The VCL-MegaConnect, 64 Port Plus - T1 Monitoring Groomer is suitable for non-intrusive monitoring of upto 32, "live" T1 traffic links, bidirectionally (i.e. in both transmit and receive directions through its 64 T1 receivers) through a high impedance (Hi-Z) path. Additionally, the equipment also provides 16 output T1 ports that shall connect the aggregated time-slots which have been non-intrusively "monitored" from the 32, "live" T1 traffic links to the user's protocol analysers, test probes, etc.

64 Port Plus - E1 Monitoring GROOMER

The VCL-MegaConnect, 64 Port Plus - E1 Monitoring Groomer is suitable for non-intrusive monitoring of upto 32, "live" E1 traffic links, bidirectionally (i.e. in both transmit and receive directions through its 64 E1 receivers) through a high impedance (Hi-Z) path. Additionally, the equipment also provides 16 output E1 ports that shall connect the aggregated time-slots which have been non-intrusively "monitored" from the 32, "live" E1 traffic links to the user's protocol analysers, test probes, etc.

32 Port Plus E1 Hi-Z Monitoring (Hi-Impedance) GROOMER

VCL-MegaConnect, the E1 x 32 port Hi-Z Monitoring Groomer is available for special non-intrusive monitoring (high impedance) applications in which E1 ports can be connected to monitoring / billing equipment for non-intrusive monitoring of live traffic or signaling, required by billing servers etc.

32 Port Plus T1 Hi-Z Monitoring (Hi-Impedance) GROOMER

VCL-MegaConnect, the T1 x 32 port Hi-Z Monitoring Groomer is available for special non-intrusive monitoring (high impedance) applications in which T1 ports can be connected to monitoring / billing equipment for non-intrusive monitoring of live traffic or signaling, required by billing servers etc.

STM-1 Hi-Z Non-Intrusive Monitoring Groomer

VCL-STM-1 Monitoring Groomer is a cost-effective monitoring and grooming equipment which may be used to "non-intrusively" monitor "bi-directional" STM-1 links through a 80:20 optical splitter patch panel and allow the user to select 64Kbps time-slots and groom them to E1 output ports, which may be then connected to E1 probes, E1 signaling analyzers and billing servers etc.

VCL-MX Version 6 DXC - 80 T1, 120Mbps Digital Access Cross Connect Switch

Orion Telecom Networks Inc. offers VCL-MX Version 6 DXC – 80 T1, 120Mbps Digital Access Cross Connect is a modular switch which may be scaled from 8 T1 Ports to up to 80 T1 Ports. The VCL-MX Version 6, E1 DACS (E1 DXC) offers full cross-connect functionality to cross-connect between 64Kbps time-slots (DS-0s), "n"x64Kbps consecutive DS-0s and Fractional E1 channels to full E1 channels.

VCL-MX Version 6 DXC - 80 E1, 160Mbps Digital Access Cross Connect Switch

Orion Telecom Networks Inc. offers VCL-MX Version 6 DXC – 80 E1, 160Mbps Digital Access Cross Connect is a modular switch which may be scaled from 8 E1 Ports to up to 80 E1 Ports. The VCL-MX Version 6, E1 DACS (E1 DXC) offers full cross-connect functionality to cross-connect between 64Kbps time-slots (DS-0s), "n"x64Kbps consecutive DS-0s and Fractional E1 channels to full E1 channels.

E1, MegaConnect Jr.Digital Access Cross-Connect Switch

The VCL-MegaConnect-Jr. 16 Port, E1 Digital Cross Connect Switch, is an E1 digital cross-connect switch, which presents its user an easy to use, yet a sophisticated platform to cross-connect up to 16, E1 ports. The VCL-DACS, E1 Digital Cross Connect Switch offers full cross connect functionality to cross-connect, and / or aggregate DS-0s, "n"x64Kbps consecutive data channels and, Fractional E1 channels to full E1 channels.

T1, MegaConnect Jr. Digital Access Cross-Connect Switch

The VCL-MegaConnect-Jr. 16 Port, T1 Digital Cross Connect Switch, is an T1 digital cross-connect switch, which presents its user an easy to use, yet a sophisticated platform to cross-connect up to 16, T1 ports. The VCL-DACS, T1 Digital Cross Connect Switch offers full cross connect functionality to cross-connect, and / or aggregate DS-0s, "n"x64Kbps consecutive data channels and, Fractional T1 channels to full T1 channels.

16 Port E1 / T1 Mixed Configuration DACS and Interface Converter

VCL-MegaConnect Jr., 16 Port E1/T1 mixed configuration DACS and interface converter shall allow the user to cross connect between E1 and T1 interfaces at DS-0 (64 Kbps time-slot) level and use it for interface, frame and line-code conversion between 8 E1 interfaces and 8 T1 interfaces.

VCL-MX Version 6, 80 E1 Voice and Data Multiplexer

Version 6 - E1 Multiplexer may be used for inter-connecting legacy networks, provisioning and managing bandwidth on a E1 channelized level as well as 64Kbps, DS-0 time-slot level and as a digital-access cross-connect equipment. Due to the changing traffic patterns, there is a need to support multiple services from the same equipment like integrated data transport, better network management etc. This necessitated evolution to next generation E1 Multiplexer. Redundant power supply options make it an ideal solution for network service providers seeking to integrate and provide legacy and the next generation services from a single platform.

PRI ISDN Q.931 Multiplexer

VCL-PRI (Primary Rate Interface) ISDN Multiplexer provides an efficient and cost-effective platform to convert 30, dial-up, analog voice circuits to a digital E1, PRI ISDN interface, as per ITU-T Q.931 recommendations.

VCL-MX, E1 Drop Insert Multiplexer

Orion's E1 Multiplexer the VCL-MX, 2Mbps E1 voice and data, drop-insert (add-drop) multiplexer provides full range of voice (POTS) and digital data services to subscribers located at different locations, requiring to interconnect and establish a voice and data network over an E1 link. The VCL-MX is available in 4 versions, each providing different features and voice / data interfaces.

E3, 34Mbps Multiplexer

E3, 34Mbps multiplexer multiplexes 16, 2Mbps E1 electrical tributries into one 34Mbps electrical stream conforming to all applicable G.703, G.823 and G.831 ITU-T (CCITT) recommendations. Available with TCP / IP Remote Access Server for remote access and monitoring.

E1 Channel Banks with Answer Supervision

Orion's E1 Channel Bank / E1 Channel Bank Multiplexer the VCL-CB-BR is used in applications to deliver voice over an end-to-end E1 (radio / fiber / HDSL) links. Features include complete line protection against difficult field condition. The E1 channel bank interface to the analog PSTN (POTS*) lines have been ruggedized to provide complete protection against line card failures which occur from induced voltages from AC power lines and lightening strikes and difficult field conditions.

VCL-CB Intelligent E1 Channel Bank

Orion introduces new intelligent E1 Channel Bank E1 Channel Bank Multiplexer the VCL-CB with Voice Activity Detection (VAD) to provide voice activated answer supervision and disconnect supervision to connect VoIP (Voice over IP), Voice over Frame Relay and Voice over ATM networks to analog PSTN (POTS) lines that do not provide any type of answer supervision / battery reversal functions.

16 E1 Plus Ethernet PDH Optical Multiplexer

Orion's VCL-16 E1 + Ethernet PDH Opical Multiplexer is a point to point high performance optical line transmission equipment, combines 16, ITU-T G.703 compliant standard electrical E1s plus 100BaseT ethernet signal into an optical data stream for transport over fiber optic pairs. Several transmitter options for different cable types and wave-lengths are available. 1+1 optical path redundancy is offered and available as an option.

VCL-1400, STM-16 / 64 SDH Multiplexer

Orion Telecom Networks Inc. offers VCL-1400 STM-16 / 64 SDH Multiplexer is a compact POTP platform which is targeted for deployment in the edge and access part of a transport network. It can be configured both as a TDM MSPP as well as a Packet Switch. It supports both TDM and Ethernet as Line Interfaces. It offers full redundancy and comes with an expansion chassis for deployment in high drop locations.

VCL-1043-STM-1/4 SDH Multiplexer, GigE-SDH Aggregator

Orion Telecom Networks Inc. offers VCL-1043-STM-1/4 SDH Multiplexer and GigE-SDH Aggregator’ is the compact Multi-Service Access Platform (MSAP) that offers Gigabit (Optical and Electrical ports), Ethernet (FE), STM-1, STM-4 and E1 aggregation functions. The Gigabit and SDH uplink (network side) interfaces can provide simultaneous services.

STM-1 63 E1 (Optical / Electrical) Add-Drop SDH Multiplexer

Orion Telecom Networks Inc. offers STM-1 63 E1 (Optical / Electrical), Add-Drop SDH Multiplexer unit is a modular platform unit with two 155.52Mbps optical / electrical interfaces, which may be used in a point-to-point, chain or ring application to provide an ultra-compact, cost effective and flexible multi-service platform.

STM-1/4/16 (VCL100) Multi-Service Provisioning Platform

Orion STM-1/4/16 is an ultra-compact, carrier class, and cost effective bandwidth provisioning equipment designed to manage and deliver services from the optical core to the access.

STM-4 SDH Add Drop Multiplexer with E1, T1, E3, E4, DS3, STM-1e, STM-1o, 10/100 BaseT Ethernet, GigE

The VCL100 STM-1/4 is a modular, and cost effective STM-1/4 SDH multiplexer equipment designed to manage bandwidth and voice & data access services over STM networks. The products are designed to support end-to-end provisioning and management of services across all segments of the optical network. It combines innovative optical networking software with the intelligence of SONET / SDH to deliver a flexible, cost-effective network solution.

Next Generation STM-1 / STM-4 SDH Multiplexers with E1, E3, E4, STM-1e, STM-1o & 10/100 Mbps Ethernet tributaries

Orion Telecom offers state-of-the-art SDH transmission solutions.

• STM-1, VCL100LT (upto 28 E1 / DS1)
• TM-1, VCL100MC-1 (upto 63 E1 / DS3)

STM-1 Optical Repeater

Orion VCL-STM-1 Optical Repeater is a cost-effective solution which allows its users to transport an optical link over an extended range by amplifying and repeating the optical signal. A 1+1 optical interface option is also offered and available in the event that two STM-1 links are required to be extended on the same optical route.

STM-1 Optical to STM-1 Electrical Converter

Orion VCL-STM-1 Optical to STM-1 Electrical converter provides a simple and cost-effective conversion between STM-1 optical interface to STM-1 electrical interface. VCL-STM-1 Optical to STM-1 Electrical converter is an interface conversion equipment supplied with one STM-1 electrical interface and one STM-1 optical interface. 1+1 option is also offered and available.

STM-1 (Optical / Electrical) Add- Drop Multiplexer

STM-1 (Optical / Electrical), E1 and Ethernet Multi-Service SDH Transmission Unit is a modular platform unit with two 155.52Mbps optical / electrical interfaces, which may be used in a point-to-point, chain or ring application to provide an ultra-compact, cost effective and flexible multi-service platform.

VCL-Gigabit Optical Add-Drop Multiplexer

Orion VCL-Gigabit Optical Add-Drop Multiplexer is a unique Gigabit multi-service optical fiber transport solution which transmits both Gigabit Ethernet (Gigabit Wire-Speed) data along with upto 16 E1 (TDM) channels over an optical fiber link.

VCL-E1 (G.703) Fiber Optic Modem (FOM)

VCL-E1 (G.703) Fiber Optic Modem (FOM) provides the user the capability to establish communication between two E1 interfaces or between an E1/FE1 interface and a "n"x64 V.35 interface over an optical fiber link. It establishes a secure, long range data fiber link between routers, multiplexers and other E1 devices.

VCL-V.35 Fiber Optic Modem (FOM)

The VCL-V.35 Fiber Optic Modem provides the user the capability to establish communication between two V.35 interfaces or between an E1/FE1 interface and a "n"x64 V.35 interface over an optical fiber link. It establishes a secure, long range data fiber link between computers, routers, multiplexers and other V.35 or E1 data communication devices.

E3, 34Mbps Optical Line Transmission equipment (OLTE)

E3, 34Mbps Opti Multiplexer, multiplexes / demultiplexes 16, 2mbps E1 electrical tributaries into a 34Mbps optical stream, transmitting on a 1310nm (1500nm optional) optical fiber to establish an optical transmission link between locations. Conforms to all the applicable G.703, G.823, G.955, G.652 and G.654 ITU-T (CCITT) recommendations. Available with 1+1 optical protection (redundancy). Powered by STM-1 grade Class I Laser - by Lucent Technologies, Inc.

8 E1 Optical Multiplexer plus Ethernet with SNMP

8 E1 + Ethernet - Optical Multiplexer is a high performance optical line transmission equipment, combines 8, ITU-T G.703 compliant standard electrical E1s plus 100BaseT ethernet signal into an optical data stream for transport over fiber optic pairs. Several transmitter options for different cable types and wave-lengths are available. 1+1 optical path redundancy is offered and available as an option.

4 E1 Optical Multiplexer plus Ethernet with SNMP

4 E1 + Ethernet - Optical Multiplexer is a high performance optical line transmission equipment, combines 4, ITU-T G.703 compliant standard electrical E1s plus 100BaseT ethernet signal into an optical data stream for transport over fiber optic pairs. Several transmitter options for different cable types and wave-lengths are available. 1+1 optical path redundancy is offered and available as an option.
Product Brochure / Data Sheet

Ethernet over Multi E1 (ML-PPP) Converter

Orion's VCL-ETH-8-ML / VCL-ETH-16-ML Converter allows the user to send Ethernet data between two points or between multiple points (maximum 12 directions), over 8 /16 E1 Links respectively. E1 Interfaces options are 75 Ohms / 120 Ohms (as per customer order). This equipment provides two Electrical Gigabit (1000 / 100 / 10M) Ethernet Interfaces (RJ-45).
Product Brochure / Data Sheet

Ethernet over FE1 Converter

Orion's VCL-ETH-FE1 Interface Converter (Desktop Version) provides the user with Ethernet over E1 conversion enabling the user to transport Ethernet data over an E1 link.

Gigabit Ethernet over SDH

Orion Telecom Networks Inc. offers Gigabit Ethernet over SDH (STM-1) Equipment is a modular platform unit with two pluggable 155.52Mbps optical / electrical interfaces, which may be used in a point-to-point application to provide a compact, cost effective and flexible solution to deliver multiple Ethernet channels.
Product Brochure / Data Sheet

Ethernet over SDH

Orion's VCL-Ethernet-over-SDH provides a simple, cost effective and compact solution to convert 10/100BaseT data interface on the user side and transport Ethernet traffic over a STM-1 SDH link and reconstruct the data back to ethernet frame format, at remote end. The converter is an effective method for converting and transporting 10/100BaseT ethernet data over an STM-1 (SDH) link.
Product Brochure / Data Sheet

DS3 to E1 and E1 to DS3 Converter

Orion E1 to DS3 and DS3 to E1 converter solutions provides upto from 8 E1 to 32 E1 interface to DS3 and DS3 to upto 32 E1s. These converters may be installed in a 19 inch VCL-MegaConnect chassis in any "mix" for converting "n" x E1 interfaces to DS3 interfaces. (Note: The value of "n" is in multiples of 8 E1 ports or DS3 ports). The converter provides a simple and cost effective method to convert a DS3 stream to an E1 stream.

Ethernet over E3 Switch

Orion offers its Ethernet to E3 Switch (Ethernet over E3 Switch) packaged in a 19-inch rack mountable chassis. Orion Ethernet to E3 Switch (Ethernet over E3 Switch) provides a 100BaseT data interface on the user side which may be used to transport Ethernet traffic over a E3 link. The Switch provides a simple and cost effective method to convert and transport 100BaseT ethernet data over a E3 link.

Ethernet over E1 Converter

Orion offer its Ethernet over 1 E1 converter. The 10Base-T Ethernet interface to 1 E1 interface converter which offers a channelized E1 and 10Base-T interface conversion. This equipment offers electrical level conversion between 10Base-T Ethernet interface and a G.703 / E1 (or fractional E1) interfaces.

Ethernet over 4 E1 Converter

Orion offer its Ethernet over 4 E1 converter. The 10Base-T Ethernet interface to 4 E1 interface converter which offers a channelized E1 and 10Base-T interface conversion. This equipment offers electrical level conversion between 10Base-T Ethernet interface and a G.703 / E1 (or fractional E1) interfaces.
Product Brochure / Data Sheet

Ethernet over 8 E1 Converter

Orion's Ethernet over 4/8/16E1 Converter allows the user to send Ethernet data, between two points, over E1 links. E1 Interfaces are 120 Ohms. Ethernet Interface options may be ordered as 10/100Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm/1310nm/1550nm single mode optical fiber interfaces.
Product Brochure / Data Sheet

Ethernet over 16 E1 Converter

Orion Ethernet over 16E1 Converter allows the user to send Ethernet data, between two points, over E1 links. E1 Interfaces are 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm/1310nm/ 1550nm single mode optical fiber interfaces.

Product Brochure / Data Sheet

4 Ethernet over E1 Converter

The VCL-4 Ethernet over E1 Converter provides the user with an option to transport Ethernet (multiple LANs) over an E1 link. The equipment converts and transports upto
4 x Ethernet links over an E1 in a shared* mode, or a discreet* mode, depending on the users preference and selection.

E1 to T1 Data E1 Converter

Orion T1 to E1 converter solutions provides from 8 E1s upto 64 E1 interfaces to "n" x T1s or convert "n" x T1s to upto 64 E1s. These converters may be installed in a 19 inch VCL-MegaConnect chassis in any "mix" for converting "n" x E1 interfaces to "n" x T1 interfaces. (Note: The value of "n" is in multiples of 8 E1 ports or 8 T1 ports). The converter provides a simple and cost effective method to convert a T1 stream to an E1 stream.

Ethernet to DS3 Switch

Orion offers its Ethernet to DS3 Switch (Ethernet over DS3 Switch) packaged in a 19-inch 1U (44mm) high rack-mountable chassis. Orion Ethernet to DS3 Switch (Ethernet over DS3 Switch) provides a 100BaseT data interface on the user side which may be used to transport Ethernet traffic over a DS3 link. The converter provides a simple and cost effective method to convert and transport 100BaseT Ethernet data over a DS3 link.

4 x Ethernet over T1

Orion offers its 4 x Ethernet over T1 (IP over TDM) package in a 19-inch rack-mountable chassis. It provides four 10/100BaseT (4 RJ-45) data interfaces on the user side which may be used to transport Ethernet traffic over a T1 link. The converter provides a simple and cost effective method to convert and transport Ethernet data over a T1 link.

Ethernet to E3 Converter

Orion offers its Ethernet to E3 converters (Ethernet over E3 Converters) packaged in a 19-inch rack mountable chassis. Orion Ethernet to E3 converters (Ethernet over E3 Converters) provides a 100BaseT data interface on the user side which may be used to transport Ethernet traffic over a E3 link. The converter provides a simple and cost effective method to convert and transport 100BaseT ethernet data over a E3 link.

E3 to T1 and T1 to E3 Converter

Orion offers T1 to E3 and E3 to T1 converters. Also available are E1 to T1, E1 to DS3, Ethernet to E1, T1, E3 and DS3 Converters. Orion T1 to E3 and E3 to T1 converter solutions provides upto from 8 E1 to 48 T1 interface to E3 and E3 to upto 48 T1s. These converters may be installed in a 19 inch VCL-MegaConnect chassis in any "mix" for converting "n" x T1 interfaces to E3 interfaces. (Note: The value of "n" is in multiples of 8 T1 ports). The converter provides a simple and cost effective method to convert a T1 streams to an E3 stream.

10BaseT to V.35 Interface Converter

The 10BaseT to V.35 Interface Converter is a high performance Ethernet bridge which converts a 10Base-T Ethernet to V.35 interface. With a compact size and low cost, it is ideal for low cost Ethernet bridge applications over V.35 network. It learns the MAC addresses in the linked LAN and keep them updating continuously.

E1 Automatic Protection (Failover) Switch

Orion's 4 Port E1 Protection (Failover) Switch allows the user to connect upto four E1 lines from the telephone company to "active", as well as to "standby" E1 terminal(s), such as data server(s), routers etc. at the customer premises.

E1 / T1 Automatic Protections Switching Solutions : APS (1+1)

E1 Protection Switching and T1 Protection Switching: Each E1 (or T1) redundancy switch supports one E1 (or T1) link, to upto 16, E1 (or T1) links can be supported by a "pair" of E1 (or T1) Protection Switching Systems. Two E1 (or T1) Protection Switching Systems are required (one at each end of the link) for implementation of 1+1 redundancy solution.

VCL-SafeComm, 8 E1 Links (24 E1 Ports), 1+1 Automatic Protection Switch

The VCL-SafeComm, 8 E1 Links (24 E1 Ports), 1+1 Automatic Protection Switching Equipment may be used to protect upto 8 E1 Links (24 E1 Ports), point-to-point links and provide an alternate communication route to each E1 Link between any two E1 points.

VCL-SafeComm, 8 T1 Links (24 T1 Ports), 1+1 Automatic Protection Switch

The VCL-SafeComm, 8 T1 Links (24 T1 Ports), 1+1 Automatic Protection Switching Equipment may be used to protect upto 8 T1 Links (24 T1 Ports), point-to-point links and provide an alternate communication route to each T1 Link between any two T1 points.

VCL-SafeComm, 16 E1 Links (48 E1 Ports), 1+1 Automatic Protection Switch

The VCL-SafeComm, 16 E1 Links (48 E1 Ports), 1+1 Automatic Protection Switching Equipment may be used to protect upto 16 E1 Links (48 E1 Ports), point-to-point links and provide an alternate communication route to each E1 Link between any two E1 points.

VCL-SafeComm, 16 T1 Links (48 T1 Ports), 1+1 Automatic Protection Switch

The VCL-SafeComm, 16 T1 Links (48 T1 Ports), 1+1 Automatic Protection Switching Equipment may be used to protect upto 16 T1 Links (48 T1 Ports), point-to-point links and provide an alternate communication route to each T1 Link between any two T1 points.

DS3 Fail-Over (DS3 Protection) Switch

Orion's DS3 Fail-Over (DS3 Protection) Switch allows the user to connect a single DS3 line from the telephone company to an "active", as well as to a "standby" DS3 terminal, such as data server / router etc., at the customer premises.

E3 Fail-Over (E3 Protection) Switch

Orion's E3 Fail-Over (E3 Protection) Switch allows the user to connect a single E3 line from the telephone company to an "active", as well as to a "standby" E3 terminal, such as data server / router etc., at the customer premises.

DC to DC Converter - 48 V DC (range DC 36-76) to 24V DC 4.2 Amps (100 Watts) 4 Fused Outputs

DC to DC converter may be used to convert - 48 V DC (range 36 V DC to 76 V DC) Main Input Voltage to 24 V DC output voltage.

AC to DC Converter - Desktop Version 48V DC 1.1 Amps 50 Watts

AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to -48V DC output voltage. It may be also used to convert 120V DC - 370V DC Input Voltage to -48V DC Output Voltage.

AC to DC Converter - Desktop Version 24V DC 6.3 Amps 150 Watts

AC to DC converter may be used to convert 85V AC-264 V AC, 47Hz-63Hz AC Mains Input Voltage to 24V DC output voltage. It may be also used to convert 120V DC - 370V DC Input Voltage to 24V DC Output Voltage.

AC to DC Converter - Desktop Version 48V DC 3.2 Amps 150 Watts

AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to - 48 V DC output voltage or 120 V DC to 370 V DC Input Voltage to - 48 V DC Output Voltage.

AC to DC Converter Rack Mounting Version 24V DC 6.3 Amps 150 Watts 4 Fused Outputs

AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to - 24 V DC output voltage or 120 V DC to 370 V DC Input Voltage to - 24 V DC Output Voltage.

AC to DC Converter Rack Mounting Version 48V DC 3.2 Amps 150 Watts 4 Fused Outputs

AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to - 48 V DC output voltage or 120 V DC to 370 V DC Input Voltage to - 48 V DC Output Voltage.

16 x E1, 120 Ohms DB37 (F) to 75 Ohms BNC (F) Converter Panel

The 16 x E1, 120 Ohms DB37 (F) to 75 Ohms BNC (F) Converter Panel allows 16xE1 (75 Ohms) twisted pairs (DB37 connector) to be patched to 16xE1 (75 Ohms) BNC connections.

Dual Balun (Shielded) 2 x BNC (F) (75 Ohms) to RJ-45 (F) 120 Ohms Converter

The Dual Balun converts 2 x BNC (F) (75 Ohms) to RJ-45 (F) 120 Ohms.

16 x E1 120 Ohms (RJ45) to 75 Ohms Converter (BNC Female Connector) Converter

E1, 120 Ohms (RJ45) to E1, 75 Ohms (BNC Female Connector) Converter, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (BNC Female Connector) Interfaces.

16 x E1 120 Ohms (RJ45) to 75 Ohms (M4 Male Connector) Converter

E1, 120 Ohms (RJ45) to E1, 75 Ohms (M4 Male Connector) Converter, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (M4 Male Connector) Interfaces.

16 x E1 120 Ohms (RJ45) to 75 Ohms (M4 Female Connector) Converter

E1, 120 Ohms (RJ45) to E1, 75 Ohms (M4 Female Connector) Converter, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (M4 Female Connector) Interfaces.

16 x E1 120 Ohms (RJ45) to 75 Ohms (1.6 / 5.6 Female Connector) Converter

E1, 120 Ohms (RJ45) to E1, 75 Ohms (1.6 / 5.6 Female Connector) Converter, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (1.6 / 5.6 Female Connector) Interfaces.

16 x E1 120 Ohms (RJ45) to 75 Ohms (BT43 Male Connector) Converter

E1, 120 Ohms (RJ45) to E1, 75 Ohms (BT43 Male Connector) Converter, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (BT43 Male Connector) Interfaces.

XC 64 E1 Electronic Patch Panel

XC 64 E1 intelligent electronic patch panel which allows the user to cross-connect any E1 port to any / multiple E1 ports, electronically, without having to use any external patch-cords or loosely hanging wires.

XC 64 T1 Electronic Patch Panel

XC 64 T1 intelligent electronic patch panel which allows the user to cross-connect any E1 port to any / multiple T1 ports, electronically, without having to use any external patch-cords or loosely hanging wires.

16 x E1 75 Ohms (Siemens - DIN 1.6/5.6 Connector) Patch Panel with Additional Hi-Z Monitoring Port

16 x E1 75 Ohms (Siemens - DIN 1.6/5.6 Female Connector) Patch Panel Hi-Z Monitoring Port is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications.

16 x E1 75 Ohms (Ericsson - M4 Male Connector) Patch Panel Hi-Z Monitoring Port
16 x E1 75 Ohms (Ericsson - M4 Male Connector) Patch Panel Hi-Z Monitoring Port is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications.

16 x E1 75 Ohms (Ericsson - M4 Female Connector) Patch Panel Hi-Z Monitoring Port

16 x E1 75 Ohms (Ericsson - M4 Female Connector) Patch Panel Hi-Z Monitoring Port is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications.

16 x E1 75 Ohms BNC Female Connector) Patch Panel Hi-Z Monitoring Port

16 x E1 75 Ohms (BNC Female Connector) Patch Panel Hi-Z Monitoring Port is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications.

16 x E1 75 Ohms (BT43 Male Connector) Patch Panel Hi-Z Monitoring Port

16 x E1 75 Ohms (BT43 Male Connector) Patch Panel Hi-Z Monitoring Port is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications.

E1 75 Ohms 16 Port High Impedance (Hi-Z) Monitoring Patch Panel

E1 75 Ohms Patch-Panel is used for E1 Monitoring Application Connecting 75 Ohms Patch panel to live E1 traffic - Monitoring Application. The BNC Connector is used for Data IN / Data OUT from the 75 Ohm E1 links which are required to be monitored. Data IN of Patch-Panel (BNC) will be connected to Transmit / Data OUT of E1 Port. Data OUT of Patch-Panel (BNC) will be connected to Receive / Data IN of E1 Port. 120 Ohms (RJ45) E1 of the Patch-Panel will connect to VCL-MegaConnect using "Y" cable

E1 120 Ohms, 16 Port High Impedance (Hi-Z) Monitoring Patch Panel

E1, 120 Ohms, 16 Port High Impedance Monitoring Patch Panel is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications. It is primarily designed to patch up to 16, E1 circuits. It also, simultaneously, provides up to 16 high-impedance (Hi-Z) outputs on it's monitoring (MON) port(s) from which, both the transmit (Tx) and the receive (Rx) signals of the patched E1 link can be "tapped non-intrusively" (i.e without disturbing or loading the active E1 link(s) in any manner).

T1 100 Ohms, 16 Port High Impedance (Hi-Z) Monitoring Patch Panel

T1, 100 Ohms, 16 Port High Impedance Monitoring Patch Panel is primarily designed for applications where T1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications. It is primarily designed to patch up to 16, T1 circuits. It also, simultaneously, provides up to 16 high-impedance (Hi-Z) outputs on it's monitoring (MON) port(s) from which, both the transmit (Tx) and the receive (Rx) signals of the patched T1 link can be "tapped non-intrusively" (i.e without disturbing or loading the active T1 link(s) in any manner).

Optical Splitter

1x2 Optical Splitters in 90:10 and 80:20 ratios. The Optical Splitters "split" the input optical signal received by it between two optical outputs, simultaneously, in a pre-specified ratio.

16 x E1 Splitter (120 Ohms)

16 x E1 Splitter (120 Ohms) "Splits" the E1 signal that it receives between two E1 ports, by monitoring the same E1 signal on two ports, simultaneously. It may be used in application that require the E1 signal input to be simultaneously connected to active terminal equipment, while at the same time connecting it to "shadow" equipment such as call loggers, voice call recorders, data recorders or any other such equipment that does not load the active E1 link in any way and connects to the live E1 links non-intrusively.

16 x T1 Splitter (100 Ohms)

16 x T1 Splitter (100 Ohms) "Splits" the T1 signal that it receives between two T1 ports, by monitoring the same T1 signal on two ports, simultaneously. It may be used in application that require the T1 signal input to be simultaneously connected to active terminal equipment, while at the same time connecting it to "shadow" equipment such as call loggers, voice call recorders, data recorders or any other such equipment that does not load the active T1 link in any way and connects to the live T1 links non-intrusively.